Search Inventory    Search Products & Site

New Holland W50C ZB

Model W50C ZB for sale at Rusler Implement, Colorado

Double tap to zoom



Both W50C and W80C are here to provide comfort at work and let you reduce downtime. A spacious cab incorporates a standard LCD display and natural, ergonomic controls.

The choice of one or two auxiliary hydraulic circuits and the availability of high flow in combination with creep speed allows work to be done at max flow at a constantly low forward pace.

The weight distribution enables the new compact wheel loader to fully benefit from its impressive improved lifting capacity.

The Inch & Brake pedal progressively disengages the transmission in the decelerating phase while progressively engaging the brakes, giving the operator millimetric control of the machine at low speeds.



The entire range boasts 3.4 litre Common Rail F5H engines developed by FPT Industrial that comply with the stringent Stage V emissions regulations. Advanced Common Rail technology delivers precise fuelling for optimal response and has also reduced fuel consumption significantly compared to previous models. This super-quiet engine develops up to 75hp and up to 314Nm of torque for guaranteed productivity and operator comfort. The entire range uses Diesel Oxidation Catalyst (DOC) Diesel Particulate Filter (DPF) technology for Stage V compliance, which is maintenance-free and further enhances efficiency to reduce total cost of ownership.

New Holland are not going it alone when it comes to Stage V technology, they can draw on the experience of their in-house engine development specialist: FPT Industrial.
Pioneers: Common Rail technology developed by FPT Industrial at their R&D excellence center in Arbon, Switzerland in the 1980s and brought it to the masses in 1997 on the Alfa Romeo 156. They were the very first to introduce it on agricultural machines on the TS-A tractor. Pioneering. Always.
Cleaner: For the ninth consecutive year, CNH Industrial has topped the Dow Jones Sustainability World and Europe Indexes for the Industrial Engineering sector. Cleaner. Everywhere.
Proven: FPT Industrial have already produced over 345,000 F5C engines since the launch in 2007. Reliability. Confirmed.

• DOC & DPF technology is used to meet Stage V emissions regulations
• Diesel Oxidation Catalyst converts pollutants present in the exhaust stream to harmless substances such as carbon dioxide and water
• DPF: Diesel particulate filter removes particulate matter from the exhaust gases
• Maintenance free after treatment system
• No need for AdBlue

• Your compact wheel loader receives precisely the amount of fuel it requires, maximum power is produced at 2500rpm
• The optimised combustion process results in more efficient engines which are better able to respond to your demands

• Service intervals have been further extended to an industry leading 500 hours
• Saving both time and money!

Reducing fuel consumption
• With the use of Common Rail, DOC and DPF technology across the range, fuel consumption has been reduced significantly
• Precision fueling is key to fuel efficiency


All models in the range are equipped with hydrostatic transmissions, you just press the accelerator and go, smoothly and without fuss. Maximum road speed is 21 MPH when the optional High Travel Speed is specified, more than fast enough to get from A to B around the farm. With the inching & brake pedal, more power can be diverted to the loaders hydraulics without disconnecting the drive, while maintaining a constant engine rpm, useful in manure handling for example. A creep speed option is also available on all models except the W50C, whereby the travel speed can be set and adjusted in the 3 MPH speed.

• The Inch & Brake pedal progressively disengages the transmission in the decelerating phase while progressively engaging the brakes
• Fine control of the machine is achieved at low speeds
• With the same precision you can accomplish every task with the all-in-one joystick with flow memory button
• The 3rd or 4th functions are proportionally controlled


• On the two smallest models there is a 67l/min pump running at 2500rpm
• On the larger two models there is a choice of the standard 85l/min pump or the High Flow pump producing 130l/min
• On all models the pump powers both the hydraulics and the steering, and for safety, there is a priority valve to favor the steering demand

• The High Flow option comes with the new Creep Speed, which provides maximum hydraulic flow at constant speed in the 0 to 5.5km/h range
• Front electrical socket and Return De-pressurized drain complete the package

The new compact wheel loader range features a steering angle of 40° to each side, fully hydraulic center pivot steering, emergency steering function and the front and rear wheels follow the same track

• The rear axle on the C series oscillates to a total angle of 20 degrees, improving both safety and stability
• Compared to a machine with an oscillating center pivot, rear axle oscillation gives operators better perception of the machines stability
• The Glide-Ride system, self activated only when needed over 5.5km/h, prevents arm bouncing

There are 2 differential configurations:
• Limited slip front and rear (all models)
• Open with 100% lock on front and rear differentials (W70C - W80C)


W50C ZB  
Cab height in (mm) 97” (2458)
Wheelbase in (mm) 82” (2075)
Ground clearance under shaft in (mm) 17” (444)
Ground clearance under axles in (mm) 13” (321)
Angle of departure in (mm) 28°
Overall width without bucket in (mm) 69” (1740)
Tread width in (mm) 55” (1400)
Operating height - fully raised with spillguard in (mm) 154” (1400)
Hinge pin height - fully raised in (mm) 122” (3136)
Overall length - bucket level on ground in (mm) 206” (5283)
Dump height - fully raised, 45° dump in (mm) 97” (2490)
Bucket reach - fully raised, 45° dump in (mm) 30” (766)
Bucket reach - 7 ft 0 (2.13m), 45° dump in (mm) 43” (1102)
Dig Depth in (mm) 3” (73)
Turning radius: outside in (mm) 146” (3721)
Turning angle: From center degrees 40
Turning angle: Total angle degrees 80
Turning angle: Rear axle oscillation, total degrees 18
Voltage volts 12
Alternator amps 120
Batteries 95 AHR, 900 CCA
Pump (steering/implement) Open-centered pressure/flow compensated. Fixed gear pump
Loader control valve Open-center, Hydraulic Loader Control with single lever includes: Forward/Neutral/Reverse switch, Floating switch, Low/High Travel mode switch, Auxiliary Function Roller
Loader auxiliary steering Hydraulic orbital center-pivot articulating w/on-demand oil flow
Filtration 15-micron, full flow replaceable cartridges on return line
Flow at 2500 rpm gpm (lpm) 18 (67)
Main relief pressure psi (bar) 3335 (230)
Pump Additional HF pump
Flow at 2500 rpm gpm (lpm) NA
Pressure psi (bar) NA
Lift cylinder(s) two
Bore diameter in (mm) 3 (70)
Rod diameter in (mm) 2 (51)
Stroke in (mm) 29 (728)
Dump cylinder: Bore diameter in (mm) 3 (83)
Dump cylinder: Rod diameter in (mm) 2 (44)
Dump cylinder: Stroke in (mm) 19 (492)
Model F5HFL463B*F001
Type 4-stroke
Cylinders 4 cylinders
Fuel injection High pressure common rail injection
Fuel Diesel
Fuel Filter Replaceable, full flow
Air filter Dry type element w/ warning restriction indicator
Radiator Core type Staggered
Fan Direct drive
Lubrication/cooling oil pump Integral
Engine oil SAE 10W40 CJ-4 Diesel SAE 0W40 CJ-4 Diesel
Pump Deep sump plate cooler with pressurized under-piston nozzles
Bore in. (mm) 3.898 (99)
Stroke in. (mm) 4.33 (110)
Displacement liters 3.4
Pump operating angles: Side-to-side degrees Rated 35
Pump operating angles: Fore and aft degrees Rated 35
Pump operating angles: Oil filtration Replaceable, full flow
Engine speed: Rated speed, full load rpm 2500
Engine speed: Low idle rpm 950
Engine speed: High idle, no load rpm 2500
Horsepower @ 2500 rpm Gross hp (kW) 58 (43)
Horsepower @ 2500 rpm Net hp (kW) 55 (41)
Peak torque @ 1400 rpm Gross lb. ft. (N·m) 181 (245)
Peak torque @ 1400 rpm Net lb. ft. (N·m) 185 (251)
Transmission Hydrostatic transmission
Planetaries Outboard
Pump relief psi (kPa) 6 (42)
Pump flow @ 2500 rpm gpm (L/min) 26 (100)
Differential Open or LSD
Differential ratio 3.67
Planetary ratio 6
Final axle ratio 22
1st ratio 1.85
2nd ratio NA
Service brakes Single pedal. Not assisted, Hydraulic Brake pump with control of the “Inching” function. Auto refill system with auxiliary fluid tank. Caliper on front axle
Parking brake Mechanical control lever, Single dry disk on input of the front axle, Mechanical Caliper with no auto wear adjustment
Turtle - Forward mph (km/h) 3 (5)
Turtle - Reverse mph (km/h) 3 (5)
Rabbit - Forward mph (km/h) 12 (20)
Rabbit - Reverse mph (km/h) 12 (20)
High speed - Turtle - Forward mph (km/h) NA
High speed - Turtle - Reverse mph (km/h) NA
High speed - Rabbit - Forward mph (km/h) NA
High speed - Rabbit - Reverse mph (km/h) NA
Fuel tank gal. (l) 23 (87)
Total gal. (l) 15 (57)
Reservoir gal. (l) 11 (40)
Front Axle gal. (l) 2 (9)
Rear Axle gal. (l) 3 (12)
Engine oil w/ filter gal. (l) 2 (7)
Cooling gal. (l) 3 (13)
Reference configuration Unit Equipped with ROPS/FOPS cab with heater, standard counterweight, front and rear fenders, full fuel, 165 (75 kg) operator
Reference tires 12.5-18 PRMPT Dunlop Tires 12.5-18 PRMPT Dunlop Tires
Reference bucket 0.9 yd³ (0.7 m³) general purpose bucket w/ Bolt-on-Edge
Operating weights lb. (kg) 11,111 (5040)
With optional counterweight lb. (kg) NA
Fork weight with V type Coupler lb. (kg) 772 (350)
Forks length in. (mm) 47 (1200)
Fork load center in. (mm) 20 (500)
Max height below forks in. (mm) 114 (2903)
Ground-Fork Clearance @ max Reach in. (mm) 50 (1266)
Payload (80% of FTTL - EN 474-3) lb. (kg) 4004 (1816)
Tipping load - straight lb. (kg) 6019 (2730)
Tipping load - 40° turn lb. (kg) 5004 (2270)
Payload (80% of FTTL - EN 474-3) w/ add cwt lb. (kg) NA
Tipping load with add cwt- straight lb. (kg) NA
Tipping load with add cwt - 40° turn lb. (kg) NA
Dump angle - fully raised degrees 45
Max. rollback: Ground degrees 39
Max. rollback: Carry Position degrees 47
Max. rollback: @ Maximum reach degrees 69
Max. rollback: @ Full height degrees 73
Maximum back dragging angle degrees 42
ISO bucket capacity - Struck yd3 (m3) 0.7 (0.5)
Heaped yd3 (m3) 1.0 (0.7)
Bucket width - outside in. (mm) 74 (1900)
Bucket weight (incl. Coupler and components) lb. (kg) 805 (365)
Operating load - ISO lb. (kg) 3538 (1605)
Maximum material density - ISO lb/yd³ (kg/m3) 3865 (2293)
Tipping load - ISO: Straight lb. (kg) 8534 (3871)
Tipping load - ISO: 40° turn lb. (kg) 7077 (3210)
Tipping load - ISO: Straight with add cwt NA
Tipping load - ISO: 40° turn with add cwt NA
Operating load with add cwt - ISO NA
Maximum material density with add cwt - ISO NA
Lift Capacity: Full height lb. (kg) 7227 (3278)
Lift Capacity: Maximum reach lb. (kg) 9200 (4173)
Lift Capacity: Ground lb. (kg) 11,669 (5293)
Breakout force with tilt cylinder lbf. (kgF) 13,356 (6058)
Loader clearance circle in. (mm) 335 (8596)